研究者詳細 - 小迫　雅裕

論文 - 小迫　雅裕

分割表示365 件中 101 - 120 件目／全件表示 >>

Partial discharge detection method for vacuum leakage diagnosis of a vacuum interrupter 査読有り

Y.Nakano, M.Kozako, M.Hikita, T.Tanaka, M.Kobayashi

IEEJ Transactions on Electrical and Electronic Engineering 14 ( 6 ) 819 - 824 2019年06月

記述言語：英語掲載種別：研究論文（学術雑誌）

© 2019 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc. Vacuum circuit breakers (VCBs) have been widely used in the medium distribution voltage range of 12–38 kV for more than half a century. Recent interest for them is because of the loss of vacuum in a vacuum interrupter (VI). Generally, the leakage is an improbable event during the expected lifetime of typically 20–30 years, while there are some reports that VIs beyond their expected lifetime have a significantly higher leakage rate. To keep the high reliability of middle voltage VCB, even for the high voltage VCB, it is necessary to develop the earlier detection method of vacuum leakage from VI. In the present study, an experimental setup with a partial discharge (PD) detecting system for detecting vacuum leakage from a test VI was constructed. The internal pressure of VI was arbitrarily regulated in the range of 0.02–100 Pa through an insulating tube using several valves. A detecting resistor of 1 kΩ was connected to a plane electrode located outside 115 mm away from VI to measure the PD current due to discharges inside the VI. A current transformer (CT) was also placed below the plane electrode. Sensors with different specification for PD detection, such as a transient earth voltage sensor, a horn antenna, and an acoustic emission sensor, were investigated and characterized. As a result of pressure dependence of PD inception voltage, it follows the left side of Paschen's Law in the pressure range more than 2.0 Pa, while no discharges occurred below 2.0 Pa. To analyze the PD charge and rise time from measured waveforms, the PD mechanism in the medium voltage range inside the VI was discussed. © 2019 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.

DOI： 10.1002/tee.22870

Scopus

その他リンク： https://www.scopus.com/inward/record.uri?partnerID=HzOxMe3b&scp=85063226605&origin=inward

開閉インパルス電圧繰返し重畳と油隙内部の状態が油浸紙-絶縁油複合絶縁系の部分放電特性に与える影響査読有り

吉積弘将, 小迫雅裕, 匹田政幸, 藤井祐樹, 中村勇介, 長広明

電気学会論文誌B 139 ( 6 ) 446 - 454 2019年06月

Development and evaluation of SiC inverter using Ni micro plating bonding power module 査読有り

A.Kawagoe, T.Itose, A.Imakiire, M.Kozako, M.Hikita, K.Tatsumi, T.Iizuka, I.Morisako, N.Sato, K.Shimizu, K.Ueda, K.Sugiura, K.Tsuruta, K.Toda

2019 IEEE International Workshop on Integrated Power Packaging, IWIPP 2019 36 - 39 2019年04月

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）

France Toulouse 2019年04月24日 - 2019年04月26日

© 2019 IEEE. This paper reports on evaluation of inverter system using silicon carbide (SiC) power module with a novel packaging technology of Ni micro plating bonding. The power module is developed to make the structure maximize the performance of SiC attracting attention in recent years. As a result, it was found that the developed inverter reduces the inverter loss and improves the efficiency of the entire inverter system as compared with in-vehicle product using Si-IGBT and the inverter consisting of the conventional package structure using SiC MOSFET. Moreover, it was confirmed that switching was possible even when the chip temperature exceeded 200°C, suggesting that the developed inverter can be driven under the high temperature environment.

DOI： 10.1109/IWIPP.2019.8799079

Scopus

その他リンク： https://www.scopus.com/inward/record.uri?partnerID=HzOxMe3b&scp=85071582937&origin=inward

Drastic Change in Non-Linear Resistive Materials I(V) Characteristics 査読有り

Belijar G., Hermette L., Kozako M., Hikita M.

2019 IEEE International Workshop on Integrated Power Packaging, IWIPP 2019 97 - 101 2019年04月

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）

France Toulouse 2019年04月24日 - 2019年04月26日

© 2019 IEEE. Non-linear Resistive Materials are thought to be able to solve aging issues due to intense electric field near triple junction in DBC/AMB substrate of power module. In present study, non-linear I(V) behavior of epoxy/ZnO microvaristor is characterized. Large change in the I(V) characteristic is observed during successive measurements, meaning that material degradation occurred. Optical microscopy of the material surface gave an insight of the phenomenon leading those modifications, an hypothesis on the degradation mechanism is proposed.

DOI： 10.1109/IWIPP.2019.8799097

Scopus

その他リンク： https://www.scopus.com/inward/record.uri?partnerID=HzOxMe3b&scp=85071566871&origin=inward

Construction and verification of novel insulation defect location system with high space resolution for next generation power module 査読有り

Maki J., Matsuzoe T., Kozako M., Hikita M., Nakamura Y., Taniguchi K., Ikeda Y., Okamoto K.

2019 International Conference on Electronics Packaging, ICEP 2019 325 - 328 2019年04月

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）

Japan Niigata 2019年04月17日 - 2019年04月19日

© 2019 Japan Institute of Electronics Packaging. This paper reports on construction and verification of a high space resolution partial discharge (PD) location system for the next generation power module. A novel PD location method (polarity reversion method) is proposed by calculating electromagnetic wave (EMW) propagation characteristics inside the power module using finite difference time domain (FDTD) analysis. In addition, EMW signal characteristics under AC voltage and impulse voltage application are compared. Based on these results, an automatic PD location system has been successfully constructed under the impulse voltage application.

DOI： 10.23919/ICEP.2019.8733578

Scopus

その他リンク： https://www.scopus.com/inward/record.uri?partnerID=HzOxMe3b&scp=85068316694&origin=inward

High temperature dielectric property of silicon nitride insulating substrate for next generation power module up to 350 degrees Celsius. 査読有り

Abe T., Nishigaki Y., Kozako M., Hikita M.

2019 International Conference on Electronics Packaging (ICEP2019) 444 - 448 2019年04月

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）

Japan Niigata 2019年04月17日 - 2019年04月19日

© 2019 Japan Institute of Electronics Packaging. Recently, as power module tends to have higher output density, large-capacity and downsizing of the module are demanded. It also tends to operate at higher temperatures. From the above circumstances, evaluation of high temperature electrical properties of ceramic insulating substrates for application of next generation power module becomes important. However, there are very few reports on the high temperature insulation property of the ceramic insulating substrate. This paper presents dielectric properties (relative permittivity ϵr, relative dielectric loss factor ϵr″ and AC conductivity σac) of ceramic insulating substrate consisting of Silicon Nitride (Si3N4) used for next generation power module up to high temperature of 350 °C. Besides, DC conductivity σdc are evaluated as a function of the temperature of the substrate, from which the activation energy Ea was calculated. Thus obtained results are discussed with the temperature dependence of the permittivity and ac conductivity considered. An attempt is also made to evaluate specific properties of the Si3N4 substrate by comparing with the dielectric properties of Aluminum Nitride (A1N) substrate.

DOI： 10.23919/ICEP.2019.8733529

Scopus

その他リンク： https://www.scopus.com/inward/record.uri?partnerID=HzOxMe3b&scp=85068314191&origin=inward

過渡接地電圧法による部分放電信号の低周波成分伝搬メカニズムの考察査読有り

吉積弘将, 小迫雅裕, 匹田政幸, 藤井祐樹, 中村勇介, 長広明

電気学会論文誌A 139 ( 3 ) 154 - 160 2019年03月

マイクロ発泡皮膜電線の部分放電開始電圧に及ぼす巻付け時の機械的ストレスの影響査読有り

久保智洋, 前田健太, 小迫雅裕, 匹田政幸, 福田秀雄, 池田佳祐, 冨澤恵一, 武藤大介

電気学会論文誌A 139 ( 3 ) 161 - 166 2019年03月

Volume-Time理論を用いた発泡皮膜線ツイストペアのインパルス部分放電開始電圧の推定査読有り

前田健太, 久保智洋, 小迫雅裕, 匹田政幸, 福田秀雄, 池田佳祐, 冨澤恵一, 武藤大介

電気学会論文誌A 139 ( 3 ) 167 - 173 2019年03月

研究調査委員会レポート：パワーモジュールの電気絶縁信頼性に関する調査専門委員会査読有り

小迫雅裕, 早瀬悠二, 岸直哉

電気学会論文誌．　Ａ ( 一般社団法人電気学会 ) 139 ( 9 ) NL9_4 - NL9_4 2019年01月

Study on static electrification of the PFAE-mineral oil mixture 査読有り

Rajab A., Gumilang H., Tsuchie M., Kozako M., Hikita M., Suzuki T.

IOP Conference Series: Materials Science and Engineering 602 ( 1 ) 2018年11月

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）

Indonesia Padang, 2018年11月08日 - 2018年11月09日

© 2019 IOP Publishing Ltd. The natural ester of tri-ester type has been implemented on a high voltage large power transformer, rated at 420 kV, since 2014. The high voltage transformer is known prone to the static electrification risk. Palm fatty acid ester (PFAE) which is a monoester oil type has also been tried on the high voltage power transformer. For a retrofilling purpose, some portion of the previously used insulating oil (it is mainly mineral oil) will remain in the transformer. It is then demanded to study the static electrification of a mixture of PFAE and mineral oil. This paper presents an investigation results on the static electrification properties of PFAE-mineral oil mixture at various percentage ratios of PFAE. The results show that charging tendency (ECT) increase with the percentage ratio of PFAE, but then decreases for the oil containing only PFAE. On the other side, the resistivity of oil mixtures decreases with the increase of percentage ratio of PFAE but then increases for the oil containing only PFAE.

DOI： 10.1088/1757-899X/602/1/012016

Scopus

その他リンク： https://www.scopus.com/inward/record.uri?partnerID=HzOxMe3b&scp=85073232997&origin=inward

Discharge Characteristics and Mechanisms under Medium Vacuum Region in Vacuum Interrupter 査読有り

Y.Nakano, S.Masuda, M.Kozako, M.Hikita, T.Tanaka, M.Kobayashi

The 11th International Workshop on High Voltage engineering (IWHV2018) ( ED-18-092 SP-18-044 HV-18-126 ) 2018年11月

Electric Field Relaxation Effect of Micro-varistor/epoxy Composite 査読有り

K.Abe, S.Harada, Y.Nakano, M.Kozako, M.Hikita, T.Yamamoto, S.Okabe

Conference on Electrical Insulation and Dielectric Phenomena (CEIDP) 2018-October 167 - 170 2018年10月

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）

Mexico Cancun 2018年10月21日 - 2018年10月24日

© 2018 IEEE. To reduce the size of electric power equipment and enhance its reliability, the electric field stress around spacer in gas insulated switchgear (GIS) should be considered. For the electric field relaxation to such a solid insulation system, a non-linear resistive material (NRM) seems effective. NRM is a composite of micro-varistor and epoxy, and it has excellent non-linear V-I characteristic. This paper deals with verification of the effect of NRM on the field relaxation using a model simulating epoxy spacer with NRM in comparison with metal embedded spacer. By embedding NRM under the electrode, the electric field of the triple junction (TJ) composed of the electrode, gas and insulator can be relaxed by 72 % under the impulse voltage (10 kV). In addition, it can also reduce the electric field concentration by 73 % at the embedded tip in AC voltage.

DOI： 10.1109/CEIDP.2018.8544813

Scopus

その他リンク： https://www.scopus.com/inward/record.uri?partnerID=HzOxMe3b&scp=85059784888&origin=inward

Evaluation of Dielectric Strength of Tricyclopentadiene / Silica Microcomposites 査読有り

Y.Ookubo, M.Kozako, M.Hikita, N.Kamei

The 2018 Conference on Electrical Insulation and Dielectric Phenomena (CEIDP) 2018-October 594 - 597 2018年10月

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）

Mexico Cancun 2018年10月21日 - 2018年10月24日

© 2018 IEEE. Hydrocarbon-based thermosetting resins have properties such as low viscosity, low dielectric constant and high heat resistance as compared with epoxy resins and are expected to be applied to electric devices in the future. However, hydrocarbon-based thermosetting resins have not been put into practice as an electrically insulating material yet. Therefore, it is necessary to understand the electrical characteristics. Generally, when organic polymeric material is used as an insulator for high voltage equipment, a large amount of loading of inorganic fillers is needed so as to decrease linear expansion coefficient. Therefore, it is crucial to investigate the effect of inorganic filler loading on the various properties such as mechanical, thermal, and electrical properties for higher voltage and longer term operation of highvoltage equipment. From the viewpoints, this paper deals with electrical insulation properties of the hydrocarbon-based thermosetting resin with loaded micro silica particles. As a result, breakdown strength of hydrocarbon-based thermosetting resin is equal or higher than that of the epoxy resin. As a result, it can be said that the hydrocarbon-based thermosetting resin with lower viscosity and lower dielectric constant than the epoxy resin is promising as an insulating material for the next generation high voltage equipment.

DOI： 10.1109/CEIDP.2018.8544821

Scopus

その他リンク： https://www.scopus.com/inward/record.uri?partnerID=HzOxMe3b&scp=85059739415&origin=inward

Basic Study on Partial Discharge Detection with High Sensitivity using Ferrite Core 査読有り

H.Yoshikawa, S.Masuda, Y.Nakano, M.Kozako, M.Hikita, T.Mawatari, T.Matsumoto

The 2018 International Conference on Condition Monitoring and Diagnosis (CMD2018) ( P62 ) 2018年09月

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）

Australia Perth 2018年09月23日 - 2018年09月26日

© 2018 IEEE. Recently, deterioration of insulation in power equipment such as power cables due to partial discharge (PD) can give rise to crucial accident in power systems. To prevent serious failures in power equipment, on-site monitoring and early PD detection is important. In the present study, a new PD detection method using ferrite core (FC), which is inexpensive and easy to install, is proposed. FC is generally used to remove high frequency noises using its resistance component increasing with the frequency. As basic study on PD detection with various kinds of FCs, the frequency dependence of impedance was investigated. As a result, FC was found to provide much higher PD detection sensitivity than a high frequency current transformer (HFCT). The number of FC installed and its type were also found to give a great influence on the sensitivity and frequency band in PD detection. In conclusion, it was shown that FC is applicable for PD detection in power equipment.

DOI： 10.1109/CMD.2018.8535822

Scopus

その他リンク： https://www.scopus.com/inward/record.uri?partnerID=HzOxMe3b&scp=85059071335&origin=inward

Design and Fabrication of 3-D Cube UHF Antenna for Partial Discharge Detection 査読有り

A.Fauzan, U.Khayam, Suwarno, M.Kozako, M.Hikita

The 2018 International Conference on Condition Monitoring and Diagnosis (CMD2018) ( P68 ) 2018年09月

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）

Australia Perth 2018年09月23日 - 2018年09月26日

Simulation of Electromagnetic Wave and Surface Current Caused by PD for Seeking Better Detection Sensitivity by TEV Sensor Attached with a Bucket 査読有り

A.Fauzan, U.Khayam, Suwarno, H.Yoshizumi, M.Kozako, M.Hikita

The 2018 International Conference on Condition Monitoring and Diagnosis (CMD2018) ( P12 ) 2018年09月

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）

Australia Perth 2018年09月23日 - 2018年09月26日

© 2018 IEEE. Partial discharge (PD) is one of electrical phenomena which might occur in high voltage (HV) cable joint. Many methods have been tried to detect PD for cable joints installed in a manhole. Among them, an attempt is made to detect PD by transient earth voltage (TEV) sensor attached inside a metal bucket which is brought down into the manhole. This PD detection method can be used to diagnose the cable joint condition and to ensure safety of the personnel before entering the manhole. This paper presents simulation of electromagnetic wave emitted by PD and induced surface current flowing on the surface of the metal bucket to enhance the PD detection sensitivity. The simulation was made with a three-dimension finite difference time domain (FDTD) simulation software (CTC Co.; MAGNA TDM version 8.3) by changing the bucket depth, diameter, aperture angle and material, as well as excitation frequency of PD source and distance from the bucket. As a result, it was found that an optimal metal bucket shape providing the highest detection sensitivity in terms of the surface current is bucket with 0° aperture angle (cylindrical shape), outer diameter 300 mm, bucket depth 150 mm for iron material with 1mm in thickness under the circumstances of the manhole in which the cable joints are installed.

DOI： 10.1109/CMD.2018.8535615

Scopus

その他リンク： https://www.scopus.com/inward/record.uri?partnerID=HzOxMe3b&scp=85059098771&origin=inward

Partial Discharge Location in Cast Resin Transformer by Multiple Small Loop Sensors 査読有り

T.Fujimura, S.Masuda, Y.Nakano, Μ.Kozako, Μ.Hikita, Y.Nakamura, K.Iida, T.Umemura, T.Maeda, M.Higashiyama

The 2018 International Conference on Condition Monitoring and Diagnosis (CMD2018) ( P64 ) 2018年09月

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）

Australia Perth 2018年09月23日 - 2018年09月26日

© 2018 IEEE. In epoxy cast resin power apparatus, there exist unexpected insulation defects of voids and delamination. Existence of such defects can generate partial discharge (PD) with degradation of the epoxy, which eventually leads to electrical breakdown with crucial damage to the insulation systems. Thus, early PD detection and specifying the location for such defects is important. This study presents PD location in epoxy cast resin transformer of rated voltage of 6.6 kV by detecting electromagnetic (EM) wave emitted by PD using several small loop sensors. As a result, it was found that the signal intensity and arrival time difference of EM wave detected with two loop sensors can confine the defect area. Furthermore, the arrival order of EM waveforms by sensor position was measured using arrayed four loop sensors, which can locate PD in more detail. Other experimental results on PD location using X-ray irradiation to the cast resin transformer including voids was found to correspond to that provided by the present four loop sensors' PD location method. In addition, the advantage of defect location of LS was confirmed by comparison with other sensors.

DOI： 10.1109/CMD.2018.8535916

Scopus

その他リンク： https://www.scopus.com/inward/record.uri?partnerID=HzOxMe3b&scp=85059068440&origin=inward

Estimation of Internal Pressure of Vacuum Interrupter by Measuring Partial Discharge Current 査読有り

Y.Nakano, S.Masuda, M.Kozako, M.Hikita, T.Tanaka, M.Kobayashi

28th International Symposium on Discharges and Electrical Insulation in Vacuum (ISDEIV2018) 2 611 - 614 2018年09月

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）

Germany Greifswald 2018年09月23日 - 2018年09月28日

© 2018 IEEE. Loss of vacuum in vacuum interrupter (VI) is becoming an interesting theme for VI used in medium voltage range beyond its lifetime of typically 20-30 years. The early detection of abnormality in the vacuum insulated equipment must be important for the development of higher voltage vacuum circuit breakers (VCBs), such as cubicle type gas insulated switchgear (C-GIS) with compressed gas and/or insulation gas. In the present study, for the purpose of diagnosing the vacuum pressure in VI by a partial discharge (PD) measurement, PD characteristics in medium vacuum range of 1 Pa to 100 Pa were investigated. As a leakage gas, air was sealed into the VI, and its pressure was regulated from 2.2 Pa to 100 Pa, which corresponds to the left region of Paschen curve. From PD current waveforms by detecting resistor connected to plane electrode outside the VI, the charges, occurrence frequency and phase characteristics of PDs for each applied AC voltage and internal vacuum pressure were determined. It was concluded that a number of occurrence of PD and PD charges would be dominant parameter for determination of the internal pressure of VI.

DOI： 10.1109/DEIV.2018.8537045

Scopus

その他リンク： https://www.scopus.com/inward/record.uri?partnerID=HzOxMe3b&scp=85059606564&origin=inward

Discussion on Partial Discharge Measurement Technique of Cable Joint in Three Phase High Voltage Overhead Transmission Line 査読有り

S.Masuda, T.Fujimura, Y.Nakano, M.Kozako, M.Hikita, H.Haruyama, K.Miyazaki, H.Sat, F.Aono

The 2018 International Conference on Condition Monitoring and Diagnosis (CMD2018) ( P61 ) 2018年09月

記述言語：英語掲載種別：研究論文（国際会議プロシーディングス）

Australia Perth 2018年09月23日 - 2018年09月26日

© 2018 IEEE. Cable joint in high voltage overhead transmission line connecting a pole transformer is one of the important accessories. Reliable diagnostic technique for possible insulation failures in cable joint due to the long-term operation and aging is required. The purpose of this research is to establish the insulation diagnostic technique for the cable joint by measuring partial discharge (PD), which is a precursor phenomenon of dielectric breakdown. In this paper, PD signals in three-phase high voltage overhead transmission lines with 6.6 kV cable joints, actually used in electric power company, were measured by using various sensors, i.e., high frequency current transformer (HFCT), monopole antenna, and transient earth voltage (TEV) sensor. As a result, it is shown that HFCT shows the highest sensitivity for PD detection among three kinds of sensors. It is also shown that the arrival time difference of the PD signals detected by several HFCTs enables to determine the PD source in neighboring two utility poles. Furthermore, the intensity and the polarity of first arrival part of the PD signals detected by several HFCTs enable to determine the PD source in a particular cable joint among the three ones in a utility pole.

DOI： 10.1109/CMD.2018.8535875

Scopus

その他リンク： https://www.scopus.com/inward/record.uri?partnerID=HzOxMe3b&scp=85059098273&origin=inward

　前のページ - 次のページ　

<小迫 雅裕>

論文 - 小迫 雅裕

<小迫　雅裕>

論文 - 小迫　雅裕